698–960MHz & 1710–2690MHz Sector Dual-Beam Antenna | RET RCU

, , , ,

This dual-beam sector antenna is designed for high-capacity LTE and 5G macro cell deployments. It features two independently controlled beams, integrated Remote Electrical Tilt (RET), and full support for AISG 2.0/3GPP protocols. With coverage across 698–960MHz and 1710–2690MHz, this antenna provides exceptional flexibility and performance for multi-band cellular networks.

  • Frequency Bands: 698–960MHz / 1710–2690MHz
  • Polarization: ±45° dual polarized
  • Gain: 15–18dBi (band dependent)
  • VSWR: ≤1.5

Key Features

  • Dual-beam design for enhanced azimuth coverage
  • Frequency support: 698–960MHz + 1710–2690MHz
  • RET integrated (AISG 2.0/3GPP compliant)
  • RCU built-in with 2×8 pin connectors
  • High front-to-back ratio and low PIM
  • IP65-rated for outdoor use

Applications

  • Urban LTE/5G macro cell deployments
  • Sector-based site expansion
  • Co-location of low-band and mid-band spectrum
  • Redundant beam configurations for link reliability

Why Choose This Antenna?

  • Simplified RET control and reduced cabling
  • Dual-beam improves coverage and interference control
  • Compatible with existing base station infrastructure
  • Engineered for long-term outdoor durability

FAQs

  • Q: What is a dual-beam antenna?
    A: A dual-beam antenna contains two independent beam paths, allowing for split-sector configurations or redundant coverage within a single enclosure.
  • Q: What does RET do?
    A: RET (Remote Electrical Tilt) allows you to change the vertical angle of radiation remotely, helping to optimize coverage without physical adjustment.
  • Q: Is this antenna compatible with AISG controllers?
    A: Yes. It supports AISG 2.0 and 3GPP-compliant controllers for RET and RCU management.
Electrical specifications
Frequency Range (MHz)R1/R2-698~960×2
698~803 790~862 824~894 880~960
Polarization±45°
Gain at mid tilt (dBi) 14.6 15.0 15.4 15.6
Gain over all tilts (dBi) 14.4±0.5 14.8±0.5 15.2±0.5 15.4±0.5
Horizontal 3dB beamwidth (°) 68±6 64±5 63±5 61±5
Vertical 3dB beamwidth (°) 11.5±1.2 10.5±0.6 10.0±0.5 9.4±0.6
Front to back ratio (dB) Total power, ±30° >22 >23 >23 >24
Cross polar ratio (dB) (at Boresight) >15 >16>16>16
Electrical downtilt (°)2~12
Sidelobe suppression (dB) (First sidelobe above main beam) >15 >15 >15 >15
VSWR<1.5
Isolation: intra-system (dB) ≥25
Isolation: inter-system (dB) ≥25
Intermodulation IM3 (2×43dBm carrier) ≤-150 dBc
Impedance (Ω)50
Max. power per input (W) @50°C400
Lightning protectionDc Ground
Electrical specifications
Frequency Range (MHz)Y1/Y2,Y3/Y4-1710~2690×4
1710~1990 1920~2200 2200~2490 2490~2690
Polarization±45°
Gain at mid tilt (dBi) (Bottom) 17.5 17.9 18.5 18.4
Gain over all tilts (dBi) (Bottom) 17.3±0.9 17.7±0.6 18.3±0.6 18.2±0.6
Gain at mid tilt (dBi) (Top) 17.1 17.5 18.2 18.0
Gain over all tilts (dBi) (Top) 16.6±0.9 17.3±0.6 18.0±0.6 17.8±0.6
Horizontal beam centers (°) ±29 ±27 ±25 ±22
Horizontal 3dB beamwidth (°) 35±3 33±3 32±3 31±3
Vertical 3dB beamwidth (°) 9.3±0.6 8.4±0.6 7.3±0.6 6.7±0.5
Front to back ratio (dB) Total power, ±30° >25
Electrical downtilt (°)2~12
Sidelobe suppression (dB) (First sidelobe above main beam) >15
VSWR<1.5
Isolation: intra-system (dB) ≥25
Intermodulation IM3 (2×43dBm carrier) ≤-150 dBc
Impedance (Ω)50
Max. power per input (W) @50°C200
Lightning protectionDc Ground
Mechanical specifications
Connector12×4.3-10-Female
Connector position Bottom
Height × width × depth (mm2080×499×198
Packing size (mm)2465×670×330
Antenna weight (kg)38
Installation kit weight (kg)5.4
Packing weight (kg)55
Wind load (N,at 150km/h) Frontal/Lateral/Maximum 1100/325/1240
Max. wind velocity (km/h) 216
Radome material Fiberglass
Radome colorGray
Mechanical tilt (°)0-10
Operating temperature (℃) -50~65
Mounting hardware (mm)Ф50~Ф115
Mechanical specifications
RET type Integrated (Replaceable)
RET protocol AISG 2.0/3GPP
Power supply(V) 10-30 DC
Power consumption(W) ≤0.6 (Idle,12V),≤6 (In motion,12V)
Adjustment time (Full Range) <4Mins
Adjustment cycles >50,000
Temperature range (℃) -40~65
Lightning protection 3KA(8/20μs) @ Pin5 & Pin3;
5KA(8/20μs) @ Pin1 / Pin6 & Pin7
Connectors 2×8 Pin circle connector according to IEC 60130-9 and AISG. Daisy chain in:Male,Daisy chain out:Female Pin1:12V;Pin3:RS485B;Pin5:RS485A;Pin6:10-30V; Pin7:GND;Pin2&Pin4&Pin8:N/C
Technical requirementsThe manufacturer of the supplied antennas is one of the Participants in the development of technical requirements for N-P-BASTA sectoral antennas (https://www.ngmn.org/aboutus/our-partners.html). Full adherence to the recommendations from NGMN when testing antennas described in: “Recommendation on Standards for Passive Base Station Antennas v 12.”
698–960MHz & 1710–2690MHz Sector Dual-Beam Antenna | RET RCU
698–960MHz & 1710–2690MHz Sector Dual-Beam Antenna | RET RCU
Quality Commitment

Why Trust Lxelec? Why Choose Our Products?

At Lxelec, we are committed to delivering only high-quality RF antenna products. Our strict quality assurance procedures ensure consistent performance and reliability in even the most demanding environments.

  • VSWR & Gain tested to meet specifications
  • Polarization & radiation pattern verified in anechoic chambers
  • Environmental tests: temperature, humidity, UV, salt spray, vibration
  •  
  • ISO 9001 certified quality management system

  • RoHS & CE compliant

  • Traceable serial numbers and batch control

  • Third-party reports available

  • Designed for 5–10 years lifespan

  • IP-rated waterproof and dustproof options

  • Stable from -40°C to +85°C

  • Expert RF support for deployment
  • Customization for gain, connectors, cables, frequency bands
  • Fast, responsive after-sales service
  •  

Leave a message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Scroll to Top

Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
Looking for a Custom Antenna Solution?
We are continuously expanding our product catalog, but we can manufacture any type of antenna to meet your specific needs! Whether you require base station antennas, Omni Ceiling Antenna, or custom wireless solutions, we’ve got you covered.

Tell us your requirements, and our team will get back to you shortly!

Custom antenna solutions

Please fill out the form below and our expert team will contact you as soon as possible with a personalized antenna solution.